 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SUBMINIATURE Basic Switch Subminiature Basic Switch s s s s s D2MQ Super compact switch weighing only 0.3 g. Ideal for reducing equipment weight Angle terminal allows operation from the side when mounted to a PCB Despite its compact size, the snap action mechanism gives it superior electrical characteristics Silver-plated contact. Gold-plated contact also available for loads under 50 mA Ideal for use on equipment with stringent space and reliability requirements, such as in compact audio equipment, optical devices, and communications equipment Ordering Information Pin plunger Leaf lever Straight terminal Left-angle terminal Right-angle terminal Actuator Pin plunger Leaf lever Contact Silver-plated (Ag-P) Gold-plated (Au-P) Silver-plated (Ag-P) Gold-plated (Au-P) Part Number Straight Terminal D2MQ-1 D2MQ-1-105 D2MQ-1L D2MQ-1L-105 Left-angle Terminal D2MQ-1-TL -- D2MQ-1L-TL -- Right-angle Terminal D2MQ-1-TR -- D2MQ-1L-TR -- Note: The angle of the terminal illustration above is from the side of the arrow shown on the right. s CONTACT FORM Specifications Ratings Electrical ratings Inrush current Ag-Plated contact: 50 to 500 mA, 30 VDC (resistive load) Au-Plated contact: 5 to 50 mA, 30 VDC (resistive load) NC: 0.5 A max. (Ag-P), 0.05 A max. (Au-P) NO: 0.5 A max. (Ag-P), 0.05 A max. (Au-P) D2MQ D2MQ Characteristics Operating speed Operating frequency Contact resistance Insulation resistance Dielectric strength Vibration Shock Ambient temperature Humidity Service life Weight Note: Data shown are of initial value. Malfunction durability Mechanical durability Malfunction durability Operating Mechanical Electrical Mechanical Electrical 0.1 mm to 0.5 m/second (0.004 to 19.7 in/second) at pin plunger 60 operations per minute 20 operations per minute 100 m max. (initial) 100 M min. (at 250 VDC) 500 VAC, 50/60 Hz for 1 minute between terminals of same polarity 500 VAC, 50/60 Hz for 1 minute between current-carrying metal part and ground 10 to 55 Hz, 1.5 mm double amplitude 1,000 m/s2 min, (approx. 100 g min.) 300 m/s2 min. (approx. 30 g min.) -15 to 70C (with not condensation) 35% to 85% RH 30,000 operations min. (at full OT value) 10,000 operations min. (at full OT value) Approx. 0.3 g s CHARACTERISTIC DATA Mechanical service life Electrical service life Number of operations (x103) Overtravel (mm) Number of operations (x103) Switching current (A) 2 D2MQ D2MQ Dimensions Unit: mm (inch) Pin Plunger D2MQ-1 (Straight terminal) D2MQ-1-TL (Left-angle terminal) D2MQ-1-TR (Right-angle terminal) D2MQ-1-105 (Straight terminal) Operating characteristics OF max. RF min. PT max. OT min. MD max. OP 120 g 20 g 0.4 mm (0.016 in) 0.1 mm (0.004 in) 0.1 mm (0.004 in) 5.7 0.2 mm (0.22 0.01 in) Leaf lever D2MQ-1L (Straight terminal) D2MQ-1L-TL (Left-angle terminal) D2MQ-1L-TR (Right-angle terminal) D2MQ-1L-105 (Straight terminal) Operating characteristics OF max. RF min. PT max. OT min. MD max. FP* max. OP 60 g 8g 2.4 mm (0.09 in) 0.3 mm (0.01 in) 0.7 mm (0.03 in) 9.6 mm (0.38 in) 6.7 0.5 mm (0.26 0.02 in) *Free position s TERMINALS Straight terminal Left-angle terminal Right-angle terminal Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. 3 D2MQ D2MQ Precautions s MOUNTING Mount firmly using M1.4 screws and 1 kg-cm tightening torque. Mounting hole matching dimensions s SOLDERING Holding the switch at the free position, solder the lead wire to its terminal within 3 seconds, using a soldering iron rated at less than 15 W with a tip temperature of less than 280C. Excess wattage or prolonged heating can deteriorate the electrical characteristics of the switch. s OPERATION When mounting onto a metal body, always install a separator between the switch and the mounting panel. Design the insulation separator (made up of hard material) into the shape shown below. Separator shape Set the operating force of the pushbutton and leaf lever at less than twice the OF standard value. Always make the OT value larger than the specification value. Do not change the operating position of the actuator. Do not operate at extremely slow speed; also do not use the switch with its pushbutton located between the free position and the operating position. Mount the pin pushbutton type in such a way that the stroke of the pushbutton and the stroke of the operating control overlap on a vertical line. Do not operate the switch roughly as it may deteriorate the functions of the switch. Do not apply excessive force to the actuator of the leaf lever type along its operating direction, opposite to its operating direction, or in the lateral direction. Omron Europe B.V. EMA-ISD, tel:+31 23 5681390, fax:+31 23 5681397, http://www.eu.omron.com/ema Cat. No. GC SW5 4 4/98 Specifications subject to change without notice. Printed in the U.S.A. |
Price & Availability of D2MQ-1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |